Free Shipping in the USA on nearly all items!
Limited phone hours during the Holidays! Call us: 888-611-9305
Free Shipping in the USA on nearly ALL items! Limited phone hours during the Holidays!
The Samsung LM301H and LM301B are close relatives. They share the same 3.0 × 3.0 mm package and the same electrical ratings. The “H” marks the version Samsung specifies and markets for horticulture, with output stated as photon flux for plants. The “B” is the general-lighting version. In a finished grow light, the driver, board layout, heat management and light spread decide your results far more than the letter on the diode. Whichever you choose, compare the whole fixture.
This guide is for home growers, beginners, urban growers with a tent and commercial cultivators who see “Samsung LM301” on a spec sheet and want to know what it means for their canopy and their budget.
Both are mid-power LEDs. A mid-power LED is a small chip run at low current, and a fixture uses dozens or hundreds of them spread across a board. That spread gives smoother light than a few big chips and makes heat easier to manage.
Samsung’s LM301B datasheet describes a 0.3 W class mid-power LED in a 3.0 × 3.0 mm package. It lists a 200 mA maximum forward current, a 110°C maximum junction temperature and 7.5°C/W thermal resistance from junction to solder point. Samsung’s LM301H CRI70 datasheet lists the same 200 mA, 110°C and 7.5°C/W, a 120° beam angle and an operating range of −40 to +85°C, and labels the part for horticulture lighting.
So on the points that matter for building a fixture, size, current limits, heat path and beam angle, the two parts match. The “B” part has been used in general lighting modules, and the “H” part was introduced to serve growers directly.
The clearest difference is how each is specified.
| LM301B | LM301H | |
|---|---|---|
| Package | 3.0 × 3.0 mm (3030) | 3.0 × 3.0 mm (3030) |
| Max forward current | 200 mA | 200 mA |
| Max junction temperature | 110°C | 110°C |
| Thermal resistance (junction to solder point) | 7.5°C/W | 7.5°C/W |
| Beam angle | 120° | 120° |
| Main way output is stated | Luminous flux (lumens) | Photon flux (µmol/s) and efficacy (µmol/J) |
| Intended use | General lighting | Horticulture lighting |
Lumens describe brightness as human eyes see it. Plants respond to photons in the 400 to 700 nm range, so growers care about photon flux. A horticulture designation gives you numbers in the units a grower uses.
Samsung’s April 2019 announcement rates the LM301H at 3.10 µmol/J, measured at 25°C, 65 mA, 5000K and CRI 80. That test gives 0.56 µmol/s of photon flux per package. Samsung called it the highest photon efficacy among mid-power white LED packages at the time. Its November 2018 release introduced the original LM301H lineup at 3.03 µmol/J and 0.54 µmol/s under the same current and temperature.
Read those figures carefully. They describe one chip at 65 mA and 25°C. A real fixture runs hotter, often at a different current, and loses some light in the driver and optics. A package rating is a strong starting signal, not a fixture result.
You will see “LM301H EVO” on newer lights. It is a further development, not a rename. Samsung’s indoor farm lighting materials describe a plant-centric spectrum with a 437 nm blue peak, against 450 nm for normal full-spectrum LEDs. They give 3.14 µmol/J for the EVO against 3.08 µmol/J for the normal version, about 2% higher. They also state that efficacy holds up at higher drive currents thanks to flip-chip construction.
For you, that means EVO is the version to look for when you want the most efficient horticulture diode in a fixture. Our AC Infinity IONBEAM S11 bar uses Samsung LM301H EVO diodes in an 11-inch format, a size that suits small tents and shelves.
Two fixtures with the same diode can perform very differently. Four things change the result.
An LED is most efficient at low current. Push more current through each chip and you get more light per chip but less light per watt. A fixture with many diodes run gently can beat one with fewer diodes run hard, even when the diode name is identical. Samsung’s own 65 mA test point is a useful reference: ask how hard the fixture drives its chips relative to that.
The datasheets cap junction temperature at 110°C. Chips that run cooler last longer and hold their efficacy. Board material, heatsink size and airflow in your tent all matter. A light that sits at the top of a sealed tent with no exhaust runs hotter than the same light in a ventilated space.
The driver converts wall power to the DC current the chips need. Fixture efficacy is measured photons divided by watts drawn from the wall, so driver losses count. Dimming range, flicker behavior and safety listing (ETL or UL) also come from the driver and the build, not the diode.
The 120° beam angle spreads light widely, which is good for even coverage. How the diodes are arranged, and how far the light hangs from the canopy, decides how even your PPFD is. PPFD means photosynthetic photon flux density: the number of photons landing on one square meter of canopy each second. Our guide to PPFD for cannabis explains what it measures and why it matters at each stage.
Horticulture lighting guides, such as one published in December 2025, make the same point: a good diode from an established maker is a useful signal, but it does not guarantee a good fixture. Use this checklist when you compare two lights.
Spec sheets often quote lux or lumens. These measure light the way eyes see it and can misrepresent a light rich in red or blue. Compare photon figures, and use a PAR meter if you want to confirm what lands on the canopy. We cover the difference in our PPFD vs lux articles.
Sometimes the LM301H version of a light costs more than the LM301B version, and sometimes it does not. The price gap is set by the manufacturer, not by Samsung’s ratings alone, and it changes with each product revision.
Here is a practical way to decide.
As a rough example, take two 240 W-class lights with a 2% gap in efficacy. Over thousands of run hours across a room, that 2% shows up as power you either use or do not. For a single 2 × 4 foot tent it is small. The footprint, uniformity and heat in your tent will change your harvest far more.
The right choice depends on what you are growing in.
Small tents and shelves. Bar-style and compact fixtures with LM301H EVO diodes give you horticulture-rated chips in a form that fits tight spaces. The IONBEAM S11 is one example, and the IONBOARD S33 at 240 W steps up to a larger footprint.
Standard tents. A full-size board with many diodes run below their limit gives even coverage. The Mars Hydro Smart FC1000 with Samsung LM301B is built for larger spaces and shows how a strong LM301B fixture is put together.
Commercial rooms. Look at uniformity across the whole bench and at how many fixtures the design needs. Under-canopy lighting adds light where top lighting cannot reach, which is the purpose of our proximity systems.
Beginners. Start with a complete kit or a single well-rated fixture sized to your tent. Do not spend extra time on diode letters. Get the footprint, the hanging height and the ventilation right.
We stock fixtures built on both diode families, along with top lighting and under canopy grow lights. Our proprietary proximity systems are designed to improve light distribution under the canopy, and we report yield gains above 20% and better bud grading from them. We rate 4.8 out of 5 from more than 5,800 reviews, and most US orders ship free.
Scott
If you are choosing between fixtures, start from your tent size and your canopy target, then filter by diode. Browse the full range of LED grow lights, tents, kits and environmental controls, or go straight to top lighting for the main fixture.
For lower leaves that top lights miss, our under canopy grow lights add light at the level where it is often thin. Commercial buyers can ask about bulk orders and financing.
We sell lights with both diodes, so we have no stake in the letter. What we see as the real limit in most grow rooms is not the diode but the light the lower canopy receives. Top lights, whatever the chip, lose intensity as light passes through leaves. That is why we built our offer around under-canopy and proximity lighting: it puts photons where the plant is shaded.
Our advice is simple. Choose a fixture with a horticulture-rated diode such as LM301H or LM301H EVO when you want the most efficient chip. Choose a well-built LM301B fixture when the design and the price suit your space. Then measure PPFD across your canopy and adjust height and dimming until the numbers are even.
Our proximity systems are designed for that last step, and we have seen them lift yield by over 20% and improve bud grading. Talk to our team about your tent size and crop, and we will help you match a fixture to it.
Scott
They are very close. Samsung’s datasheets show the same 3.0 × 3.0 mm package, 200 mA maximum current, 110°C junction limit and 7.5°C/W thermal resistance. The H is the horticulture-designated version, specified in photon terms for plants.
The H gives you horticulture-rated figures such as 3.10 µmol/J at Samsung’s test point. In a finished light, the driver, heat management and light spread usually matter more. Compare measured fixture efficacy and PPFD maps between two lights.
It is a newer horticulture diode with a 437 nm blue peak. Samsung rates it at 3.14 µmol/J against 3.08 µmol/J for the normal version, and states that efficacy holds at higher drive currents.
A PAR meter measures the photons that land on your canopy, which is the figure that matters. Lux and lumens apps do not measure plant-usable light well, so rely on PPFD readings and the manufacturer’s PPFD map.
0 of 3 items selected
Leave a comment