Free Shipping in the USA on nearly all items!
Limited phone hours during the Holidays! Call us: 888-611-9305
Free Shipping in the USA on nearly ALL items! Limited phone hours during the Holidays!
A grow light spectrum chart is a graph of the colors a fixture emits. The horizontal axis is wavelength in nanometers (nm), and the vertical axis is how much light the fixture puts out at each wavelength. Read it in three steps. First, check that most of the output sits between 400 and 700 nm. Second, see how the peaks split between blue, green, red and far-red. Third, compare that split with what your plants need at their current stage. The chart shows color only. It does not show how much light reaches your leaves, and that second half decides yield.
Most charts are a line graph with a curve that rises and falls. Here is what each part means.
The horizontal axis runs in nanometers. Visible light spans roughly 400 to 700 nm, from violet and blue at the left to deep red at the right. Many charts extend a little past that to show ultraviolet (below 400 nm) and far-red (700 to 800 nm).
The vertical axis shows relative intensity, usually scaled so the tallest peak equals 100%. Some lab reports plot absolute output in µmol/s/nm instead. Resource Innovation’s LED best practices guide describes these spectral quantum distribution graphs as the laboratory-tested spectrum of a fixture, showing the share of light output at each wavelength.
The curve itself is the fixture’s fingerprint. Narrow spikes around 450 nm and 660 nm point to blue and red LEDs. A broad hump across the whole visible range points to white LEDs. A small bump past 700 nm means far-red has been added.

The shaded 400 to 700 nm band is PAR, photosynthetically active radiation. According to Virginia Tech Extension, PAR, PPF and PPFD all describe light in that 400 to 700 nm range. The same publication credits Keith McCree’s 1972 work for the photosynthetic action spectrum, often called the McCree curve. That curve is the reason red and blue dominate grow light design.
MU Extension advises that the first step when shopping is to check the manufacturer’s spectrum graph and confirm that the fixture emits in the PAR range. It also says to avoid any light whose maker supplies no spectrum graph and no PPF or PPFD figures. So a chart that is missing is already an answer.
The table below sums up the ranges published by university extension programs. Percentages are typical shares of a fixture’s output, not rules.
| Color | Wavelength | What it does | Typical share |
|---|---|---|---|
| UV | 280 to 400 nm | Can promote pigments and secondary compounds when used carefully | Rarely included |
| Blue | 400 to 500 nm | Smaller leaves, shorter stems, compact habit | Usually under 20% to 30% |
| Green | 500 to 600 nm | Usable for photosynthesis, helps you see plant health | Varies, mostly from white LEDs |
| Red | 600 to 700 nm | Main driver of growth, most energy-efficient color | Often over 70% |
| Far-red | 700 to 800 nm | Stem elongation and larger leaves in small amounts | Under 5% to 10% |
Those ranges come from the Virginia Tech guide. Here is what to look for in each band.
More blue gives plants shorter stems and smaller, thicker, darker leaves. Michigan State University’s floriculture team explains that in sole-source indoor lighting, blue light controls extension growth. North Dakota State University lighting slides add that blue-only light produces short plants with small leaves and good roots. Too much blue stunts growth, so a balanced share matters. On a chart, a tall blue peak next to a small red one is a seedling or clone profile, not a flowering one.
Green light does drive photosynthesis. It also lets you see yellowing, pests and nutrient problems under the lamp. Virginia Tech notes that green LEDs are generally less energy efficient but can improve how plants look to human eyes. That is why you will see a broad hump across the middle of a white-LED spectrum.
Red LEDs are the most efficient diodes in a fixture, so the highest-efficacy lights emit mostly red. Michigan State’s guide says this is why efficient fixtures lean red. MU Extension reports that red and far-red radiation promote plant growth and tissue expansion. If the chart shows a big peak near 660 nm, that is where most of your growth comes from.
Far-red triggers the shade avoidance response. A little encourages leaf expansion, and a lot stretches stems. A 2026 study on cannabis by Perotti and colleagues found that continuous far-red supplementation raised plant height by 9% and leaf dry weight by 16.3% compared with red plus blue alone. It did not change flowering time, because cannabis flowering is controlled by photoperiod, the length of the light and dark periods. In that study, end-of-day far-red delivered many of the benefits while using less energy.
Virginia Tech says UV is seldom included in fixtures but can promote pigments and secondary compounds when applied carefully. If your chart shows a small spike below 400 nm, that is the fixture’s UV channel.
Blue plus red (“blurple”) fixtures. Two narrow peaks with a valley between them. Virginia Tech gives a general guideline of about 20% blue and 80% red, and notes that blue:red is quantified as a ratio. A HortScience grower’s guide says no standardized light spectrum exists, but many LED makers produce roughly 80% red and 20% blue.
Broad-spectrum white fixtures. A smooth, wide curve. These are compared by Kelvin temperature (K). Lower Kelvin, such as 3,000 K, has less blue than higher Kelvin, such as 5,000 K. The HortScience guide notes that a common white LED used for growing has a red:blue ratio of 0.66, which means 40% red and 60% blue.
Full-spectrum fixtures. The term means the color mix imitates sunlight and looks fairly white. Maryland Grows explains that full-spectrum light is not required for acceptable growth and flowering, but it makes plants easier to inspect and reduces eye strain compared with harsh red and blue light. For a spare room or a grow tent you walk into daily, that comfort counts.
Tunable fixtures. Several channels you can adjust. Resource Innovation notes that tunable LEDs let growers adjust intensity and spectrum for specific cultivars and growth stages.
For a deeper look at how each band shapes growth, flowering and pigmentation, this guide on how light spectrum affects plants is a good companion to the chart.
There is no single ideal spectrum. Michigan State’s floriculture team says the right mix depends on the application (photoperiodic, supplemental or sole-source), the crop, and the response you want. Here is how that plays out in a tent.
Michigan State also points out a trade-off: you cannot get short stems and large leaves at once. More blue gives compact plants. More far-red gives taller stems and larger leaves. Choose the one that suits your space. A tight tent or a shelf in an apartment favors compact growth. A tall room favors larger leaves.
A spectrum chart is half the picture. It tells you the color mix and nothing about how much light your plants receive. Check these numbers too.
PPFD is photosynthetic photon flux density, measured in µmol·m⁻²·s⁻¹. It counts how many photons in the PAR range land on a square meter each second. Virginia Tech calls it the preferred term and unit for describing LED output as it relates to plant growth. Resource Innovation explains that PPFD depends on fixture arrangement, type and mounting height, and that it should be measured at several evenly spaced points across the canopy at one consistent height, then averaged. Our guide to measuring PPFD at home covers the tools and steps. For flowering cannabis, see our stage-by-stage PPFD guide.
Resource Innovation’s 2022 guide lists target PPFD ranges in µmol/m²/s: leafy greens 180 to 270, microgreens and herbs 130 to 250, berries 220 to 350, vegetables 350 to 600 and high-wire vine crops 450 to 600. The chart tells you whether the colors fit. PPFD tells you whether the amount fits.
Daily light integral adds up the light over a day. For steady electric light, the formula is PPFD × hours × 0.0036, which gives mol/m²/day. At 400 µmol/m²/s for 12 hours, that is 400 × 12 × 0.0036 = 17.28 mol/m²/day. Resource Innovation notes that DLI is the long-term measure that correlates with biomass. Our guide to converting PPFD to DLI and estimating energy cost walks through the same math for flowering plants.
MU Extension suggests checking efficacy in µmol/J. HPS lamps run about 0.9 to 1.7, while current LEDs are above 2.5. Two fixtures with similar charts can differ a lot here, which changes your electric bill.
A chart averages the whole fixture. A PPFD map shows the hot center and dim edges. Ask for the map, then compare it with the footprint of your tent.
In dense indoor canopies, upper leaves absorb most of the light and the lower branches sit in shade. A perfect spectrum on paper does little for a leaf that barely receives any. This is the problem our proximity systems address. Under-canopy lighting places fixtures close to the lower growth, so light reaches areas a top-mounted fixture misses. Our growers’ experience and our product design point to the same result: more even light distribution, with over 20% increases in yield and improved bud grading in setups that use our systems.
That is also where spectrum choices pay off. Once light actually reaches the lower canopy, the color mix you picked works on far more leaf area.
Most buyers study the chart and then stop. The chart is one input. The questions that decide results are how much light reaches each leaf, and how evenly.
Our work is built on the second question. Standard top-down setups leave the lower canopy short of light, and our proximity systems are designed to put light under the canopy where it is needed. That is how we see more than 20% higher yields and better bud grading.
Our advice for beginners: choose a red-dominant fixture with some blue, confirm the PPFD at your canopy height, and then add under-canopy light as the plants fill in. For experienced growers, a tunable top light plus under-canopy supplements gives you spectrum control and coverage in one system.
Scott
Once you can read the chart, matching it to a space is simple. For a tent or shelf, look for a top light with a red-heavy mix and the PPFD map for your footprint. Our Top Lighting collection covers those fixtures. To bring light to the lower canopy, browse our Under Canopy Grow Lights. If you want adjustable channels, the Medic Grow Spectrum X has 3-channel control, 880 watts and a UV and IR timer. For a far-red or deep red option, see the TotalGrow Deep Red Bar. Our customers rate us 4.8 out of 5 across more than 5,800 reviews, and our team gives advice for beginners and commercial cultivators alike. Most US orders ship free.
Browse the full range of LED grow lights, tents, kits and environmental controls at LED Grow Lights Depot.
There is no single best one. A red-dominant mix of about 80% red and 20% blue is the common baseline, per HortScience. Adjust blue up for compact plants and add a little far-red for larger leaves.
Not for growth. Maryland Grows notes that full-spectrum light is not required for acceptable growth and flowering. It does make plants easier to inspect and reduces eye strain compared with red and blue only fixtures.
They are wavelengths in nanometers. 400 to 500 nm is blue, 500 to 600 nm is green, 600 to 700 nm is red and 700 to 800 nm is far-red. Photosynthesis happens mainly between 400 and 700 nm.
No. It shows color mix. Intensity at the canopy is PPFD in µmol·m⁻²·s⁻¹, and the daily total is DLI. Look for both on the product page, plus a coverage map for your tent size.
In the 2026 Perotti study, continuous far-red changed plant height and leaf growth but not flowering time. Photoperiod, the light and dark schedule, controls flowering in cannabis.
0 of 3 items selected
Leave a comment