Free Shipping in the USA on nearly all items!
Limited phone hours during the Holidays! Call us: 888-611-9305
Free Shipping in the USA on nearly ALL items! Limited phone hours during the Holidays!
An under-canopy fan is a small circulation fan set low in a grow tent. It moves air through and beneath the foliage, where an overhead fan and the exhaust fan do not reach well. For most tents, the answer is a quality clip-on fan aimed low and across the plant base, set to a gentle speed and oscillating, working alongside your exhaust fan. We carry clip-on fans for grow tents for this job.
This guide covers what the fan does, where to put it, how to size it, how to combine it with ventilation, and what goes wrong.
In a dense canopy, the air in the lower third of the plant stops moving. The leaves above shade it, the substrate gives off moisture, and nothing pushes the air along. A fan placed low fixes this by keeping air moving around the lower stems, the pots and the underside of the leaves.
Three things happen when that air moves.
1. The leaf boundary layer gets thinner. Every leaf is wrapped in a thin film of still air called the boundary layer. Michigan State University’s extension publication says wind speed has the greatest influence on boundary layer thickness. When that layer is thick, humidity at the leaf rises and CO2 falls. Water and nutrient uptake can slow, and the same publication links this to nutrient problems such as calcium deficiency.
2. Humidity pockets break up. Damp air that sits inside a thick canopy invites mold and mildew. Air moving through the canopy carries that moisture away from the leaves and the stems.
3. The plant responds to movement. A gentle breeze flexes stems. Plants answer by building sturdier stems, which matters when flowers get heavy. A technical guide from a US mechanical contractor for grow facilities, Harris Company’s grow facilities snapshot, notes that a controlled breeze strengthens stems into more robust plants. It also states that an under-canopy system delivers consistent, controllable circulation to every plant, which fixed wall or floor fans cannot match.
The lower tent zone has a second job. Still air around the pots and the top of the substrate stays damp. Damp substrate is where fungus gnats and root-zone moisture problems start. A fan aimed low across the pots helps the top layer dry between waterings.
Growers often buy by blade diameter. What the plant feels is air speed at the leaf.
Michigan State University gives a recommended wind speed for horizontal airflow fans of 50 to 100 feet per minute, about one foot per second. That is a light breeze. A 2024 computational fluid dynamics study in the journal Agronomy found that airflow of 0.1 to 1.3 meters per second promoted photosynthesis and transpiration by improving gas exchange and cutting boundary layer resistance. The same study showed airflow direction and speed shape how air travels through a canopy. Low airflow, by contrast, leaves uneven temperature gradients under the lamps.
The takeaway for a home grower: you want steady, moderate movement everywhere in the canopy, not a strong jet in one spot. A fan with many speed settings and oscillation gives you that control.
Large flower rooms use measured targets. A commercial airflow engineer quoted by MMJ Daily suggests starting near 100 feet per minute in the first week of flower and raising it to about 250 feet per minute by week four. Speed then tapers to around 225 in the final week. The same piece reports an average of about 50 feet per minute beneath the canopy, with under-bench fans covering gaps where plant spacing and defoliation limit airflow. The engineer also recommends mapping airflow and temperature across the room with a handheld anemometer during the first few cycles, so fan speeds are set from data and not from the first sign of mold.

You do not need that for a 4x4 tent. The principle carries over, though: airflow should reach the whole space, including the lowest part.
Placement matters more than the fan model. Use this routine.
In hydroponic setups, do not aim a fan directly at an open nutrient reservoir. Moving air across the surface speeds evaporation. That concentrates the solution and shifts your EC readings. Point the fan at the plants, not the water.
A fan low in the tent also dries splashes and runoff on the tent floor, which helps cut down on mildew in the corners. Aim it so it sweeps the floor edge as it oscillates.
For most small tents, think in pairs.
| Tent size | Typical circulation setup |
|---|---|
| 2x2 or 2x4 | One clip fan at canopy level, plus a second low fan if the canopy is dense |
| 4x4 | One fan above the canopy, one under it |
| 5x5 and larger | Two to three oscillating fans, placed on opposite sides so air loops through the tent |
This is a starting layout, not a rule. Dense plants, high plant counts and heavy training all raise the need for low airflow. Sparse canopies need less.
A 6-inch oscillating clip fan is a common size for hobby tents. Our 6-inch clip-on fan from Spider Farmer is made for this kind of tent. If you want finer control, the AC Infinity CLOUDRAY S9 2-pack gives you two 9-inch clip fans, one for the top and one for the bottom. The listing describes an EC motor, 10 wind modes, 10 fan speeds and 10 levels of auto oscillation.
A slightly larger fan run at a reduced speed is often easier to tune than a small fan at full power. Variable speed lets you dial the airflow down when plants are small and up when they fill the tent.
Circulation and ventilation are two separate jobs.
The common layout is a passive intake low on one side, an exhaust fan high on the opposite side, and circulation fans stirring the space in between. One fan sits above the canopy. One sits below. Because the exhaust is only one air stream, it cannot stir every pocket, and that is why the low fan matters.
If you are sizing the exhaust side, read our guides on ventilation for LED grow lights and why LED growers add 30 to 40% CFM to tent ventilation. CFM is cubic feet per minute, the volume of air a fan moves. Filters, bends in the ducting and tight tents all reduce what the fan actually delivers, which is why those guides add headroom.
For the exhaust side, we stock a 4-inch ventilation kit and fan range. Two examples with variable speed control are the Spider Farmer 4-inch inline fan, 205 CFM and the AC Infinity CLOUDLINE LITE A4 quiet inline fan system. A speed controller lets you run the exhaust quietly and keep it from fighting with your circulation fans.
A low fan alone leaves the top of the canopy, where lamp heat collects, without good air movement. Growers who have run only low fans report rot in the upper flowers. Pair the low fan with one above the canopy so the whole plant is covered, and keep the exhaust running. One note: if your fixtures are LEDs, heat load near the top is lower than with older lamps, but it still needs air moving across it.
Wind burn shows up as leaves that curl, claw or dry at the edges on the side facing the fan. It comes from air that is too strong, too constant or aimed too directly. To avoid it:
More airflow is not always better. Excess turbulence stresses plants mechanically and can leave moisture imbalances. Consistent, moderate airflow does more for the plant than aggressive wind.
If outer leaves flutter and the middle sits still, flowers there are at risk of moisture buildup. Add a lower fan that pushes air upward through the plant, or thin the interior growth so air can pass.
Seedlings and clones have small leaves and little root. Keep fans farther away and on low speed until the plants are established. Raise speed gradually as the canopy fills in.
Clip fans can rattle on tent poles. Tighten the clip, add a bit of padding, and choose a fan with a quiet motor if the tent is in a bedroom or living space. This matters for urban growers in small apartments.
If you manage a larger flower room, the same logic applies at scale. Fixed wall or floor fans have limited speed control and struggle to give every plant the same airflow, according to the Harris Company technical snapshot. Under-bench or under-canopy circulation fills the gaps. Plan fan counts per bench, use variable-speed units, and map airflow across the room as described above. For bulk orders and financing options on commercial purchases, see our commercial range.
Airflow is the part of a grow that people set up once and forget. We think of the tent as a system: the light, the fans and the plants all affect each other.
Our own work is built around getting light and air into the lower canopy. Our proprietary proximity systems are designed to improve under-canopy light distribution, and we have seen that growers who fix light penetration usually need to fix lower airflow too. A canopy that lets light reach the lower branches also needs air to move there.
That is why we put clip fans, inline fans and speed controllers next to our lights. Our customers include home growers, beginners who need a complete setup, and commercial cultivators. Our satisfaction rating is 4.8 out of 5 across more than 5,800 reviews.
Our advice is simple: pick a clip fan with speed control, put one low and one high, and tune by watching the leaves.
Scott
We sell LED grow lights, grow tents and kits, environmental controls and accessories, with expert advice for beginners and experienced growers. Most orders ship free in the US. For circulation, start with our clip-on fans and add an inline fan with a controller for exhaust.
If you also want to light the lower canopy, browse our under canopy grow lights. The whole range is on LED Grow Lights Depot.
In a dense canopy, they are very useful. Air above the plants moves, but the lower zone often stays still and damp. A fan aimed low keeps that air moving and helps the whole plant. Small, open plants may need less.
Aim it across the plant base with a slight upward angle, so air passes through the stems and up through the foliage. Pair it with a second fan above the canopy so the top is covered too.
Run the lowest speed that makes the leaves move gently. A light breeze of about 50 to 100 feet per minute is the range Michigan State University recommends for horizontal airflow fans. If leaves curl or dry on the side facing the fan, lower the speed or move it back.
Yes. Circulation fans stir the air already in the tent. The exhaust fan removes heat and humidity and brings in fresh air. Each does a different job, and a tent needs both.
Many growers keep circulation fans running around the clock because still air at night lets humidity build. A fan with speed control lets you turn it down when lights are off. Watch your humidity readings and adjust.
0 of 3 items selected
Leave a comment